亚洲三区在线观看无套内射,无码专区天天躁天天躁在线,自拍 偷拍 日韩,自拍欧美一区二区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

shearing machine cylinder Sold to New Zealand

Release time:2023-11-06 22:53:46 Hits: Current position: Home > News

This article mainly introduces:

New Zealand shearing machine cylinder,shearing machine cylinder manufacturer

New Zealand shearing machine cylinder

(New Zealand shearing machine cylinder,produced by Hengyu Hydraulic Cylinder Factory)

shearing machine cylinder are widely used in New Zealand,because of no need for deceleration device,long service life,smooth movement.So our company has designed shearing machine cylinder for customers from New Zealand.

Introduction to shearing machine cylinder:

In use, the shearing machine cylinder should try to avoid the friction iron powder or iron filings formed by buffering the plunger. When the matching gap of the buffer device is small and the transverse load on the piston rod is large, the sintering phenomenon may be caused. These friction iron powder or the metal fragments that have fallen off as a result of sintering will remain in the shearing machine cylinder.

1, the hydraulic machinery should be kept clean, in order to prevent dust and debris from falling into the oil, the tank should be sealed. 2, the oil in the tank should be replaced regularly according to the working condition. When changing the oil, the dirt and impurities accumulated at the bottom of the tank should be removed and the tank should be cleaned. 3, hydraulic oil, oil drums should be set in a clean and safe place to strengthen management. The oil drum, oil filter, oil funnel, oil pipe, etc. used should be kept clean. The oil drums for loading hydraulic oil must be cleaned in advance, and the oil drums should be dedicated and not mixed with other oil drums.

If air enters the hydraulic system, the shearing machine cylinder will not operate normally, mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced.

After chrome plating of the piston rod of the shearing machine cylinder, the surface flatness is not fully treated: After chrome plating of the piston rod surface, the method of post-plating polishing should be changed to post-plating polishing. Although it is necessary to increase the thickness of the coating before grinding (generally increased by about 0.02 in the diameter direction), it can remove chrome plating defects well, and test the binding force of the coating. In addition, due to the micro-roughness of the grinding surface, the trough can store lubricating oil, which can improve the wear resistance and extend the service life.

Answers to some questions about shearing machine cylinder:

What welding rod is used for hydraulic cylinder welding?
There are several reasons for bad welding of hydraulic cylinder: 1. There is hydraulic oil on the welding surface, wipe it with a rag, there will be bubbles in the welding process, and it will not last for a few days. You have to remove it, drain it, wash it off with gasoline and try again. 2. Open the groove before welding, it is not deep enough to use the Angle grinding machine, and can not find the accurate crack position. 3. The material of the cylinder itself is not clear, the welding performance of more than 35 steel is not good, in the factory welding needs to preheat, the welding rod should also be dried and insulated, there is no such condition on the site.

What is the safety factor of 25MPa cylinder wall thickness?
Safety factor n can take 3 cylinder material allowable stress [s]=sb/n δ/D=0.08 ~ 0.3 cylinder wall thickness δ=PMAX*D/ (2.3[s]-3PMAX) δ/D≤0.08 cylinder wall thickness δ=PMAX*D/2[s] P < 16MPa, Pmax=1.5Pn; P > 16MPa, Pmax=1.25Pn cold-drawn tube or honing tube is better!

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产又粗又长又硬超逼视频| 亚洲日韩理论在线观看| 成人网址日韩| 国产做受 高潮豆麻| 亚洲欧美一级| 国产自产精| 欧美 日 中文 一区| 性感91美女黄色小网站| 亚洲精品网页入口漫画| 拳交AV在线观看| 日韩欧美亚洲一区二区中文字幕| 伊人成人网站| 黄色电影三级片香蕉视频| 欧美在线精品不卡| 得得中文精品在线| 日本欧美一区二区有码| 婷婷五月花免费视频| 日本美国三区四区自拍小视频| 97成人免费福利| 久久久久久久久久久久久久性高潮| 久久亚洲精品影视| 国产日韩精品一区二区三区在线| 亚洲 日韩 丝袜 熟女 变态二区| 日韩精品人妻AV| 色诱视频ww网站| 大香蕉免费大香蕉免费| 国产午夜激情国产一区二区| 欧美一区二区不卡在线观看| 国产中文欧美在线| 欧美秘 无码一区二区三在| 三区黄片入口| 欧美日韩成仁影院| 综合激情一区| 精品国产欧美一区二区的网址| 精品一区电影国产| 亚洲网爆福利精品| 日韩中文字幕熟女少妇| 97av在线视频一区| 蜜臀午夜福| 中文永久永久字幕9| 诏安县|