亚洲三区在线观看无套内射,无码专区天天躁天天躁在线,自拍 偷拍 日韩,自拍欧美一区二区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

shearing machine cylinder Sold to Indonesia

Release time:2023-11-28 10:55:40 Hits: Current position: Home > News

This article mainly introduces:

Indonesia hydraulic cylinder,shearing machine cylinder manufacturer,shearing machine cylinder

Indonesia shearing machine cylinder

(Indonesia shearing machine cylinder,produced by Hengyu Group)

shearing machine cylinder are widely used in Indonesia,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed shearing machine cylinder for customers from Indonesia.

Introduction to shearing machine cylinder:

The wear of the hard chromium plating layer of the shearing machine cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

When the shearing machine cylinder is disassembled due to oil leakage and other faults, the position of the piston should be moved to any end position of the shearing machine cylinder by applying liquid pressure. Improper tapping and sudden drop should be avoided during disassembly.

The internal leakage of the shearing machine cylinder is an important indicator to measure the quality of the shearing machine cylinder: the internal leakage of the shearing machine cylinder will reduce the volumetric efficiency, increase the temperature rise of the oil, affect the positioning accuracy of the shearing machine cylinder, so that the shearing machine cylinder can not accurately and stably stop in a certain position of the shearing machine cylinder, so it is one of the main indicators of the shearing machine cylinder.

The repair method of shearing machine cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

Answers to some questions about shearing machine cylinder:

What steel pipe does hydraulic cylinder use? This problem is very general. Carbon steel pipe or ordinary seamless steel pipe are all ok, but then there are rolling, quilting, heat treatment and other steps, and the requirements are different, the wall thickness is different, the material is different. It depends on the circumstances.

How to distinguish the bucket cylinder from the bucket rod cylinder?
It can be distinguished according to its installation and connection: one end of the bucket cylinder is connected with the bucket; The rod cylinder is not connected to the bucket. The bucket refers to the bucket installed on the excavator. According to the working mode, it is divided into backhoe bucket and shovel bucket, the backhoe bucket is commonly used. The boom and bucket rod are working device of the excavator, usually called the big arm and the forearm, which are mainly used to control the digging and loading of the bucket. The arm connected to the frame is longer, so it is commonly known as the big arm, and its term is called the boom. The arms connected to the digging bucket are smaller, so they are commonly known as the lower arms, and the term is called the bucket rod, so they are commonly known as the big lower arms.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
亚洲一道无码一二三区| 成人一区二区欧美| 成人91福利在线视频 | 色www亚洲免费视频| 91精品人妻一区二区三区眯臀 | 日韩内射视频| 最新午夜乱码中文字幕| 国产在线视频大大大香蕉| 夜夜嗨无码AV专区| 日本一区二区人妻视频| 日韩少夫毛片| 一级片大鸡巴| 激情欧美日韩强一区| 老师张开腿让桶| 黑人广东久久久久久久| 国产免费自拍啪啪啪1234区| 国产一区h视频| 午夜毛片在线免费视频| 欧美经典三级二区| 超级碰碰碰碰碰碰| 五月丁香色综合1| 日韩黄色一级片| 乱人伦激情三十分钟| 一本道综合欧美一区| 老鸭窝日本A视频故事| 中文字幕宿舍AV| 欧美aa片一区二区三区四区| 欧美久久久久久四虎| 黄片大全1区2区| 黄片一区二区免费| 日本一区二区三区不卡在线| 尤物av午夜精品| 女优色图| AV黑丝www黄| 国产亚洲自拍色的| 亚洲妇女久久| 99re在线观看免费视频精品| 久久免费看少妇高潮A妓女网| 图片 专区 亚洲 欧美 日韩| 好吊操手机免费视频| 日韩人妻丰满后插式|