亚洲三区在线观看无套内射,无码专区天天躁天天躁在线,自拍 偷拍 日韩,自拍欧美一区二区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

Lifting cylinder Sold to Spain

Release time:2023-11-26 09:49:33 Hits: Current position: Home > News

This article mainly introduces:

Spain hydraulic cylinder,Lifting cylinder manufacturer,Lifting cylinder

Spain Lifting cylinder

(Spain Lifting cylinder,produced by Hengyu Hydraulic Cylinder Factory)

Lifting cylinder are widely used in Spain,because of long service life,smooth movement,high work efficiency.So our company has designed Lifting cylinder for customers from Spain.

Introduction to Lifting cylinder:

Lifting cylinder seal leakage causes and countermeasures: a. Loose tie rod nut will cause leakage, tighten the tie rod nut according to the torque requirements of tie rod nut, test no leakage can continue to use. b. Pressure exceeding the limit will also cause leakage. Replace the Lifting cylinder seal and re-tighten the tie rod nut to reduce the pressure to the nominal pressure range of the Lifting cylinder. c. The Lifting cylinder seal is extruded, if the O-ring is obviously extruded at the Lifting cylinder seal, replace the Lifting cylinder seal.

When installing the Lifting cylinder pipe, the pipe should be cleaned after installation, and should not pass through the Lifting cylinder block, and the by-pass pipe must be installed in front of the oil port of the Lifting cylinder block. This is important. Otherwise, the foreign body in the pipeline will enter the Lifting cylinder, and once it enters, it is difficult to exclude it, but it becomes a foreign body transported to the Lifting cylinder. Moreover, when cleaning, the removal method of foreign bodies entered in the installation pipeline operation should be considered. In addition, the corrosion in the pipe should be pickling and other procedures before the pipe installation, and the rust must be completely removed.

The Lifting cylinder pipe should not be left behind when deburring at both ends after the fixed length processing. In addition, the placement of steel pipes near the site of welding pipeline operations is the cause of welding foreign objects. The pipes placed near the welding operation site should be sealed. It must also be noted that pipe fitting materials should be fully prepared on a dust-free workbench.

The Lifting cylinder body is commonly made of No. 20, 35, 45 seamless steel pipe, and the steel pipe is honed or rolled to achieve the roughness requirement within 0.4μm. The low pressure Lifting cylinder can use 20 steel pipe, and the high pressure Lifting cylinder can use 45 steel pipe.

Answers to some questions about Lifting cylinder:

For a cylinder with a piston diameter of 100mm and a system pressure of 10MPa, what is the thrust?
Thrust is 7850 kg. Piston area A= πR^2=7850 square mm =78.5 square cm 10MPa = 100kg/cm^2 "^2" is square F = A x P =78.5 x 100=7850 kg.

How to calculate the inner diameter of the hydraulic cylinder?
These two parameters need the following information to decide: 1, pump displacement, speed (to get the actual output flow of the pump) 2, three and time requirements (lift time, drop time takes a few seconds) and then view the close cylinder series according to the results. Select the right cylinder.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
亚洲成人福利图| 舔b视频在线免费观看| 中出怀孕中文字幕在线| 日老骚逼日老骚逼日老骚逼| 天天久久美日韩| 亚洲有码一区中文| 99999日韩美精品免费视频| 欧美性感熟女丁香五月| 午夜日韩av电影| av青青国产在线| 这里只有精品日韩美| 欧美日韩狼人综合在线| 天天干,天天日AV| av手机在线观看不| 天堂殴美不卡| 97在线播放视频| 久久极品精品极品精品| 国产AV一级网站| 偷拍亚洲欧美人妻| 97精品欧美一区二区三区| 人人弄人人摸人人操| 天堂欧美一区| CaoPorn国产精品| 99黄黄色片| 天天操人人搞| 中文字幕 日韩在线| 欧美国产一区一区| 亚洲图片综合在线欧美| 很很很操美日韩欧美| 午夜麻豆传媒| 国产黄片在哪里看| 扩张脱垂一区二区三区精品| 超碰综合AV| 久久9久高清视频| 艹逼视频日逼| 91精品中文视频| 国产肛交视频一区二区三区| 欧美精品在线观看视频网站| 无码日韩第十三页| 老司机精品久久免费视频| 台湾青年精品中文字幕无码视频|