亚洲三区在线观看无套内射,无码专区天天躁天天躁在线,自拍 偷拍 日韩,自拍欧美一区二区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tailplate hydraulic cylinder Sold to Cote d 'Ivoire

Release time:2023-11-17 13:21:14 Hits: Current position: Home > News

This article mainly introduces:

Cote d 'Ivoire hydraulic cylinder,tailplate hydraulic cylinder manufacturer,tailplate hydraulic cylinder

Cote d 'Ivoire tailplate hydraulic cylinder

(Cote d 'Ivoire tailplate hydraulic cylinder,produced by Hengyu Group)

tailplate hydraulic cylinder are widely used in Cote d 'Ivoire,because of long service life,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed tailplate hydraulic cylinder for customers from Cote d 'Ivoire.

Introduction to tailplate hydraulic cylinder:

Regular maintenance of the tailplate hydraulic cylinder includes: regular tightening, tailplate hydraulic cylinder fastening screws and gland screws, tailplate hydraulic cylinder piston rod stop adjustment screws, should be tightened once a month, tighten each screw evenly, and achieve the corresponding tightening torque. Replace the seal regularly, it is recommended to replace the seal of the tailplate hydraulic cylinder once a year. Clean regularly, the tailplate hydraulic cylinder is cleaned every other year, and the seals are replaced while cleaning.

tailplate hydraulic cylinder piston sealing is best to use Yx ring, polyurethane and polytetrafluoroethylene sealing material combination, can significantly improve the sealing performance: (I), reduce friction resistance, no crawling phenomenon; (ii) Have good dynamic and static sealing, wear resistance, long service life; (iii) The installation groove is simple, and the disassembly is simple.

The tailplate hydraulic cylinder should be avoided for a long time without use, if it is indeed idle for a long time for some reason, it should also be regularly turned on for empty operation, so that its parts can be fully lubricated, so as to avoid rust on the working surface and affect the normal work in the future. (If it cannot be turned on and run, a small amount of lubricating oil can be applied on its outer surface for protection) ' The use of the tailplate hydraulic cylinder should pay attention to: the operation should be as far away from the tailplate hydraulic cylinder as possible, to avoid falling objects, knocking, rubbing the tailplate hydraulic cylinder coating. When cleaning the tailplate hydraulic cylinder, only use soft materials (such as cotton) to wipe, and do not scratch high-hardness materials. Do not use the tailplate hydraulic cylinder when the oil temperature exceeds 70 ° C.

The pressure, temperature, medium and speed of different types of seals are not the same, water-ethylene glycol medium (HFC) can not be sealed with polyurethane, it can only use rubber seal; When the tailplate hydraulic cylinder is running fast, it must be sealed with slip ring, such as Sterseal, Glairing, GD1000K, TDI, etc., when the running speed is slow, Yx, U, V combination seals can be used; Fluorine rubber seal is used in high temperature and high pressure environment; When the running speed is fast, the buffer sleeve and buffer valve must be considered.

Answers to some questions about tailplate hydraulic cylinder:

What is the relationship between medium cylinder and side cylinder ratio of forklift truck?
The middle cylinder and the side cylinder seem to have no relationship, as long as the lifting speed required by the design can be ensured, but the diameter of the cylinder can not be too thin, so as to avoid the middle cylinder acting first when the high gantry vibration lifting, and then the two cylinders acting again.

What type of seal is the cylinder of shaft 50?
You won't know the exact model until you take it apart. Oil seals have O, Y, Yx, KYx, U, UN, UHS, YA, St, Gray, Yamagata, Lei type, etc. It is difficult to know what kind of oil seal the designer chooses. Cylinder oil seal installation method: 1. Receive a fixed number of oil seals. 2. From receiving the oil seal to assembly, it must be kept clean. 3. Before assembly, check the oil seal and measure whether the size of each part of the oil seal is consistent with the size of the shaft and cavity. Before the oil seal is installed, the size of the shaft diameter should be clearly compared with the inner diameter of the oil seal. The inner cavity size should be suitable for the outer diameter width of the oil seal. Check the lip of the oil seal for damage.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
99久热综合精麻豆| 天天躁狠狠躁夜夜躁欧美| 最新中文字幕不卡av| 一区二区欧美日韩麻豆牛牛| 无码一区二区欧美| 欧美国产乱子精视频在线观看| 91色成人午夜福利| 国产精品久久久久无码AV葡京 | 中文字幕精品一二三| 色就是色亚洲性生活| 国产亚洲天堂精品| 91精品在线视频免费观看蜜臀| 欧美日韩A∨级| 五月天一区二区三区在线播放| av亚洲产国偷v产偷v自拍小说| 波多无码一区| 婷婷热这里只有精品| 欧美日韩免费一级无码| 懂色av无码国产| 欧美二精品| 操美女逼免费视频网站| 亚洲夫妻俩性生活自制视频| 成人高潮黄色av| 日本无码中文字上| 免费黄片.v v| 国产二区视频91| 中文字幕人妻系列一区| 日韩欧美第一页视频在线| 曰本一本高清色道在线| 国产一区二区三区99| 欧美一区二区三区99视频 | 国产av 久久久| 国产成人免费无码AV在线播放| 亚洲中文在线永久| 小穴被艹视频| 99精品欧美一区二区蜜| 久久久精品视频免费网站| 在线免费观看69av视频 | 午夜91日韩| a久久中文字幕| 国产91剧情一区二区在线观看|