亚洲三区在线观看无套内射,无码专区天天躁天天躁在线,自拍 偷拍 日韩,自拍欧美一区二区

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

forklift tilting cylinder Sold to Uruguay

Release time:2023-11-12 15:31:17 Hits: Current position: Home > News

This article mainly introduces:

Uruguay hydraulic cylinder,forklift tilting cylinder manufacturer,forklift tilting cylinder

Uruguay forklift tilting cylinder

(Uruguay forklift tilting cylinder,produced by Hebei Hengyu company)

forklift tilting cylinder are widely used in Uruguay,because of excellent fatigue and impact resistance,smooth movement,high work efficiency.So our company has designed forklift tilting cylinder for customers from Uruguay.

Introduction to forklift tilting cylinder:

The material of the sliding part of the forklift tilting cylinder piston sintered casting piston will cause sintering phenomenon when subjected to large transverse load. In this case, the sliding part of the piston should be made of copper alloy or welded to such material.

forklift tilting cylinder head explanation: low pressure castings, medium and low pressure with HT300 gray iron, medium and high pressure with 35, 45 steel. When the forklift tilting cylinder head itself is the guide sleeve of the piston rod, the forklift tilting cylinder head is best cast iron. At the same time, brass, bronze or other wear-resistant materials should be fused on the guide surface. If the guide sleeve is pressed into the forklift tilting cylinder head, the guide sleeve shall be wear-resistant cast iron, bronze or brass.

Before the forklift tilting cylinder is removed, the relief valve should be loosened to reduce the pressure of the hydraulic circuit to zero, and then the power supply should be cut off to stop the hydraulic device. After loosening the oil port piping, the oil plug should be applied to plug the oil port.

When purchasing the forklift tilting cylinder, try to clarify the following parameters of the forklift tilting cylinder: A. forklift tilting cylinder diameter, rod diameter, stroke; B. Working pressure or forklift tilting cylinder load; C. Working environment temperature; D. Working medium; E. Operating speed; F. Other parameters, such as connection form, mounting size, etc. In this way, the right forklift tilting cylinder type can be found accurately and quickly.

Answers to some questions about forklift tilting cylinder:

What diameter cylinder is needed for a force of 5 tons?
It depends on the pressure of your system pump. If the normal working pressure of the system is about 8MPa, then the diameter of the cylinder should be 100 mm.

How to calculate the inner diameter of the hydraulic cylinder?
These two parameters need the following information to decide: 1, pump displacement, speed (to get the actual output flow of the pump) 2, three and time requirements (lift time, drop time takes a few seconds) and then view the close cylinder series according to the results. Select the right cylinder.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
激情偷拍在线| 日本乱伦456| 88精品一区二区三区视频| 91狠狠色丁香综合久| 中日韩欧美精品| 日韩十国产十欧美十另类一区二区| 国产一级成人AV子一| 激情天天久久| 日韩欧美在线不卡一区二区| 欧美一区二区国产一区二区| 日韩在线性生活视频| 91视频一区二区入口| 韩日精品一区三区| 中文字幕久精品视频在线| 全网最黄亚洲AV| 亚洲欧美日韩高清一区 国产欧| 色五月婷激情| 免费一级片大奶子| 日韩一级特黄片| 国产视频三区六区| 国产精选h网站| 久久亚洲GV成人无码国产| 激情麻豆论坛| 操精品在线视频| 自拍亚洲欧美不卡综合 | 欧美久久久黄色电影| 啊啊 下面好大污污污视频在线观看| 久久综合亚洲麻豆kk| 换脸国产一区二区| 欧美日韩一级黄片免费看| 久久香蕉一区一区三区二区久久| 三上悠亚久久久| 久久看人妻| 精品国产成人一区二区三区网站| 日韩狠狠色av| 女女同女性一区二区三区在线| 操大美女的骚逼逼| 国产精品一区二区免费视频| 超碰在线国产一区二区| 69色久悠悠色| 免费国产夫妻性生活|